Four of the FORCE 8 Dual 4 Ohm Subwoofers Matched up to the R6 3200 Watt RMS @ 0.5 Ohm Mono Block Amplifier!
Carefully selecting each component from the Tinsel Leads to the Cast Aluminum Baskets to the 10 Gauge Wire to the Double Stacked Strontium Ferrite Magnets we have created a Subwoofer series that goes Deeper & plays Louder than our competition. Plus, our inclusion of Dual Voice Coils gives you system design flexibility. Our goal was overall design balance - the ability to play loud, play deep and remain composed. With that in mind we are proud to present the end result, “MAY THE FORCE BE WITH YOU”…
The R6 features variable low pass crossovers for system flexibility. To eliminate any possible weak link we’ve spared no expense in offering the best possible connections with Tiffany style RCA jacks for as well as an oversize Nickle plated terminal block for power input & speaker output.
Stable at 0.5 Ohm with a high quality Class D PCB layout that includes built in auto sensing turn on function for vehicles that do not have the ability for RCA output, selective Bass Boost EQ for fine tuning, soft delay remote turn on/off circuit that eliminates pops and clicks.
The R6 Amplifier utilizes a MOSFET power supply for high output and increased stability, variable gain control and remote level control port for optional controller. With dynamic features like its Parametric EQ with Q-Control and Built-In Auto Sensing Turn-On the Rage R6 Amplifier blends power and performance with sleek design allowing you to Rage in style.
FORCE 8 FEATURES
- Heavy Duty Textured Cast Aluminum Basket
- Reinforced Non-Pressed Paper Cone
- EROM Hi-Tech Ribbed Foam Surround for Strength & Flexibility
- 2.5" / 61.1mm 4-Layer Hi-Temperature Voice Coil for Extended Playing
- Double Stacked 130oz High Energy Strontium Ferrite Magnets
- Enhanced Cooling T-yoke Design with Black Anodized Finish
- Black Anodized One Piece Pole-Plate for Added Motor Force
- Customized Rubber Gasket / Magnet Boot
- 10 Gauge Oxygen Free, Pure Copper Wire
- Over Sized Mirror Image Dual Poly / Nomex Spiders
FORCE 8 SPECIFICATIONS
| Size | 8" |
| Peak Watts | 1600w (Short Bursts) |
| RMS Watts | 800w (Daily Driver) |
| Freq. Response | 20Hz ~ 250Hz |
| Displacement | 0.05 cu. ft. |
| Fs- F.A.R. | 54Hz |
| Qts | 0.41 |
| Vas | 0.09 ct. Ft. |
| X-Max (2-Way) | 24mm |
| SPL | 82dB |
| Voice Coil | 2.5" Dual 4 Ohm |
| Terminals | 10 Gauge 100% Copper Direct Input Cables |
| Basket | Die Cast Aluminum |
| Tinsel Leads | Heavy Duty Double |
| Ported Box | 18" x 14" x 12" (Round Port - One x 4" x 12") |
| Total Weight | 19 Pounds |
R6 FEATURES
- Sound Quality Class-D Design
- Built-In Auto Sensing Turn-On Function (Hi-Inputs)
- MOSFET Power Supplies for High Power Output and Best Stability into Low Impedance Loads
- Soft Delay Remote Turn On/Off Circuit Eliminates Pops and Clicks
- Variable Low Pass Electronic Crossover
- Selectable Bass Boost EQ ~ 0 ~ 12dB
- Q-Control for Narrow to Wide Parametric EQ Frequency Adjustments
- Subsonic Filter Control to Filter Out Unwanted Low Frequencies 0Hz ~ 60Hz
- Self-Diagnostic Protection Circuit with LED Status Indicator for Impedance Over-load, Speaker Short Circuit, Thermal Overheating, and DC Output
- 0.5Ω Stable Operation with Extensive Output Power Increase
- Variable Gain Control
- Remote Level Control Port (for optional controller)
R6 SPECIFICATIONS
| RMS Power @ 0.5 Ohm | 3200w x 1 |
| PEAK Power | 8000w x 1 |
| RMS @ 1 Ohm | 2300w x 1 |
| RMS @ 2 Ohms | 1300w x 1 |
| RMS @ 4 Ohms | 750w x 1 |
| Bridged RMS | N/A |
| Min Impedance | 0.5 Ohm |
| LPF / HPF | 60Hz ~ 220Hz |
| THD @ RMS Power | <1% |
| S/N (EIA Rated) | >100 dB |
| Max Voltage | 14.5v |
| RCA Voltage | 200mV ~ 10V |
| Freq. Response | 13Hz - 220kHz |
| Crossover Slope | 12dB |
| Subsonic Filter | 0Hz ~ 60Hz |
| Bass EQ | 0dB ~ 12dB |
| Subwoofer EQ | 30Hz ~ 120Hz |
| Dimensions Inches | 20.9 (in) x 2.0 (in) x 7.1 (in) |
| Dimensions mm | 531mm x 54mm x 171mm |