These Amplifiers utilize a Class A/B design for high quality and cool running under typical conditions. With a High Quality PCB layout that includes built-in auto sensing turn on function for vehicles that do not have the ability for RCA output, selective Bass Boost EQ for fine tuning, soft delay remote turn on/off circuit that eliminates pops and clicks.

With a slim footprint of only 13.5" x 10.6" x 3" this powerful amplifier subwoofer combo comes in handy for installations that are limited on space and is the perfect choice for trucks, lease cars and under the seat installations.   

• High Efficiency Class A/B Design 
• 0 ~ 180 Degree Phase Shift
• 3 Ohm Impedance
• Built-In High Level Signal Inputs (via RCA Inputs) 
• Built-In Auto Sensing Turn-On Function (Hi-Inputs)
• MOSFET Power Supplies for High Power Output and Best Stability into Low Impedance Loads
• Ground Loop Isolator 
• Soft Delay Remote Turn On/Off Circuit Eliminates Pops and Clicks
• Variable Low Pass Electronic Crossover 50Hz ~ 150Hz @ -3dB
• Self-Diagnostic Protection Circuit with LED Status Indicator for Short Circuit, Thermal Overheating
• Proprietary Noise Rejection Circuitry
• Hi-Fi E-Cap Filter with Wide Dynamic Range for Clearer Sound Reproduction
• Clipping LED Indicator  

One Fierce 8 Subwoofer (400w RMS) + One R2 Monoblock Amplifier (320w RMS)

The FIERCE8 can take up to 400 Watts RMS and has 2" Dual 4 Ohm Voice Coils that can be wired to a 2 or 4 ohm final load each.

Ribbed Foam Surrounds, Double Stacked Strontium Ferrite Magnets, Cast Aluminum Baskets and 100% Pure Copper Wire directly hard wired into the subwoofers leads. 

The R2 features variable low pass crossovers for system flexibility. To eliminate any possible weak link we’ve spared no expense in offering the best possible connections with nickel plated RCA jacks for as well as an oversize Nickle plated terminal block for power input & speaker output. 

Stable at 2 Ohms with a high quality A/B Class PCB layout that includes built in auto sensing turn on function for vehicles that do not have the ability for RCA output, selective Bass Boost EQ for fine tuning, soft delay remote turn on/off circuit that eliminates pops and clicks.

The R2 Amplifier utilizes a MOSFET power supply for high output and increased stability, variable gain control and remote level control port for optional controller. With a frequency range for a monoblock amp from 12Hz ~ 50kHz this versatile amp can power a wide range of speakers. 

What does all this translate to? Simply, amplifiers you can count on for rigorous competition and yet flexible and affordable enough to use as any system anchor.

• Heavy Duty Textured Cast Aluminum Basket
• Reinforced Non-Pressed Paper Cone 
• EROM Hi-Tech Ribbed Foam Surround for Strength & Flexibility
• 2" / 50.8mm 4-Layer Hi-Temperature Voice Coil for Extended Playing 
• Double Stacked 90oz High Energy Magnets 
• Enhanced Cooling T-yoke Design with Black Anodized Finish
• Customized Rubber Gasket / Magnet Boot
• 10 Gauge Oxygen Free, Pure Copper Wire 
• Triple Black Poly Cotton Spiders with Mirror Image Layout

• Sound Quality Class-A/B Design
• Built-In Auto Sensing Turn-On Function (Hi-Inputs)
• MOSFET Power Supplies for High Power Output and Best Stability into Low Impedance Loads
• Soft Delay Remote Turn On/Off Circuit Eliminates Pops and Clicks
• Variable Low Pass Electronic Crossover
• Selectable Bass Boost EQ ~ OFF / 6dB / 12dB
• Self-Diagnostic Protection Circuit with LED Status Indicator for Impedance Over-load, Speaker Short Circuit, Thermal Overheating, and DC Output
• 2Ω Stable Operation with Extensive Output Power Increase
• Variable Gain Control
• Remote Level Control Port (for optional controller)

Two Fierce 8 Subwoofers (800 Watts RMS) + One MR3 Micro Monoblock Amplifier (800 Watts RMS)

The FIERCE 8 can take up to 400 Watts RMS each and has 2" Inch Dual 4 Ohm Voice Coils that combined can be wired for a 1 ohm final load. The Fierce line-up is a result of our Design & Engineering team’s desire and our corporate willingness to give them a “green light” to create a Sub that’s happy whether it’s working or playing - Mission Accomplished! Belying their value-added pricing these Subs are true competitors in every aspect. The FIERCE 8 has Dual 2" Voice Coils, Ribbed Foam Surrounds, Double Stacked Strontium Ferrite Magnets, Cast Aluminum Baskets and 100% Pure Copper Wire directly hard wired into the subwoofers leads

Our compact Micro Rage Amplifiers feature MOSFET power supplies to insure an inexhaustible stream of voltage under all conditions. These Amplifiers utilize a Class D design enabling high efficiency and cool running under typical conditions. The MR3 Toro Audio Micro Sized Mono Block Amplifier is rated at 800 Watts RMS and 2000 Watts Maximum Power. Stable at 1 Ohm with a high quality Class D Digital PCB layout that includes built in auto sensing turn on function for vehicles that do not have the ability for RCA output, selective Bass Boost EQ for fine tuning, soft delay remote turn on/off circuit that eliminates pops and clicks.

The MR3 Amplifier utilizes a MOSFET power supply for high output and increased stability, variable gain control and remote level control port for optional controller.

With a tiny footprint of only 6.46" x 1.69" x 3.07" this powerful amplifier comes in handy for installations that are limited on space and is the perfect choice for motorcycles and power-sports vehicles.  

• Heavy Duty Textured Cast Aluminum Basket
• Reinforced Non-Pressed Paper Cone 
• EROM Hi-Tech Ribbed Foam Surround for Strength & Flexibility
• 2" / 50.8mm 4-Layer Hi-Temperature Voice Coil for Extended Playing 
• Double Stacked 90oz High Energy Magnets 
• Enhanced Cooling T-yoke Design with Black Anodized Finish
• Customized Rubber Gasket / Magnet Boot
• 10 Gauge Oxygen Free, Pure Copper Wire 
• Triple Black Poly Cotton Spiders with Mirror Image Layout

• High Efficiency Class-D Design for Subwoofers (MR2)
• Built-In Auto Sensing Turn-On Function (Hi-Inputs)
• MOSFET Power Supplies for High Power Output and Best Stability into Low Impedance Loads
• Soft Delay Remote Turn On/Off Circuit Eliminates Pops and Clicks
• Variable Low Pass Electronic Crossover
• Self-Diagnostic Protection Circuit with LED Status Indicator for; Impedance Over-load, Speaker Short Circuit, Thermal Overheating, and DC Output
• 1-OHM Stable Operation with Extensive Output Power Increase 
• Variable Gain Control
• Remote Level Control Port (for optional controller)
  
  

The FIERCE12 has Dual 2.5" Voice Coils, Ribbed Foam Surrounds with Heavy Duty Cast Aluminum Baskets. Carefully selecting each component from the Tinsel Leads, Direct Connected 10 Gauge Pure Copper Wire to the Double Stacked Strontium Ferrite Magnets we have created a Subwoofer that goes Deeper & plays Louder than our competition.

The R5 features variable low pass crossovers for system flexibility. To eliminate any possible weak link we’ve spared no expense in offering the best possible connections with Tiffany style RCA jacks for as well as an oversize Nickel plated terminal block for power input & speaker output. With dynamic features like its Parametric EQ with Q-Control and Built-In Auto Sensing Turn-On the Rage R5 Amplifier blends power and performance with sleek design allowing you to Rage in style.

• Heavy Duty Textured Cast Aluminum Basket
• Reinforced Non-Pressed Paper Cone
• EROM Hi-Tech Ribbed Foam Surround for Strength & Flexibility
• 2.5" / 61.1mm 4-Layer Hi-Temperature Voice Coil for Extended Playing 
• Double Stacked 250oz High Energy Strontium Ferrite Magnets 
• Enhanced Cooling T-yoke Design with Black Anodized Finish
• Black Anodized One Piece Pole-Plate for Added Motor Force
• Over Sized Mirror Image Dual Poly/ Nomex Spiders
• Reinforced Fiberglass Woven Dustcap for High Power Applications
• Dual Impedance Black Anodized Voice Coil Former with Kevlar Spunlace
• Customized Rubber Gasket / Magnet Boot
• Stitched Cone for an Extended Lifespan
• 10 Gauge Oxygen Free, Pure Copper Wire 
• Triple Black Poly Cotton Spiders with Mirror Image Layout

• 0 AWG Power / Ground Inputs 
• Sound Quality Class-D Design
  
• Built-In Auto Sensing Turn-On Function (Hi-Inputs)
• MOSFET Power Supplies for High Power Output and Best Stability into Low Impedance Loads
• Soft Delay Remote Turn On/Off Circuit Eliminates Pops and Clicks
• Variable Low Pass Electronic Crossover
• Selectable Bass Boost EQ ~ 0 ~ 12dB
• Q-Control for Narrow to Wide Parametric EQ Frequency Adjustments
• Subsonic Filter Control to Filter Out Unwanted Low Frequencies 0Hz ~ 60Hz
• Self-Diagnostic Protection Circuit with LED Status Indicator for Impedance Over-load, Speaker Short Circuit, Thermal Overheating, and DC Output
• 1Ω Stable Operation with Extensive Output Power Increase
• Variable Gain Control
• Remote Level Control Port (for optional controller)

Two Fierce 6 Subwoofers (400 Watts RMS) + One MR2 Micro Monoblock Amplifier (500 Watts RMS)

The FIERCE 6 can take up to 200 Watts RMS each and has 1.5" Inch Dual 4 Ohm Voice Coils that combined can be wired for a 1 ohm final load. The Fierce line-up is a result of our Design & Engineering team’s desire and our corporate willingness to give them a “green light” to create a Sub that’s happy whether it’s working or playing - Mission Accomplished! Belying their value-added pricing these Subs are true competitors in every aspect. The FIERCE 6 has Dual 1.5" Voice Coils, Ribbed Foam Surrounds, Double Stacked Strontium Ferrite Magnets, Cast Aluminum Baskets and 100% Pure Copper Wire directly hard wired into the subwoofers leads. 

Our compact Micro Rage Amplifiers feature MOSFET power supplies to insure an inexhaustible stream of voltage under all conditions. These Amplifiers utilize a Class D design enabling high efficiency and cool running under typical conditions. The MR2 Toro Audio Micro Sized Mono Block Amplifier is rated at 500 Watts RMS and 1000 Watts Maximum Power. Stable at 1 Ohm with a high quality Class D Digital PCB layout that includes built in auto sensing turn on function for vehicles that do not have the ability for RCA output, selective Bass Boost EQ for fine tuning, soft delay remote turn on/off circuit that eliminates pops and clicks.

The MR2 Amplifier utilizes a MOSFET power supply for high output and increased stability, variable gain control and remote level control port for optional controller.

With a tiny footprint of only 5.75" x 1.69" x 3.07" this powerful amplifier comes in handy for installations that are limited on space and is the perfect choice for motorcycles and power-sports vehicles.  

• Heavy Duty Textured Cast Basket
• Reinforced Non-Pressed Paper Cone 
• EROM Hi-Tech Ribbed Foam Surround for Strength & Flexibility
• 1.5" / 38.8mm 4-Layer Hi-Temperature Voice Coil for Extended Playing 
• Double Stacked 70oz High Energy Magnets 
• Enhanced Cooling T-yoke Design with Black Anodized Finish
• Customized Rubber Gasket / Magnet Boot
• Triple Black Poly Cotton Spiders with Mirror Image Layout
  

• High Efficiency Class-D Design for Subwoofers (MR2)
• Built-In Auto Sensing Turn-On Function (Hi-Inputs)
• MOSFET Power Supplies for High Power Output and Best Stability into Low Impedance Loads
• Soft Delay Remote Turn On/Off Circuit Eliminates Pops and Clicks
• Variable Low Pass Electronic Crossover
• Self-Diagnostic Protection Circuit with LED Status Indicator for; Impedance Over-load, Speaker Short Circuit, Thermal Overheating, and DC Output
• 1-OHM Stable Operation with Extensive Output Power Increase 
• Variable Gain Control
• Remote Level Control Port (for optional controller)
  
  

Four of the FORCE 8 Dual 4 Ohm Subwoofers Matched up to the R6 3200 Watt RMS @ 0.5 Ohm Mono Block Amplifier! 

Carefully selecting each component from the Tinsel Leads to the Cast Aluminum Baskets to the 10 Gauge Wire to the Double Stacked Strontium Ferrite Magnets we have created a Subwoofer series that goes Deeper & plays Louder than our competition. Plus, our inclusion of Dual Voice Coils gives you system design flexibility. Our goal was overall design balance - the ability to play loud, play deep and remain composed. With that in mind we are proud to present the end result, “MAY THE FORCE BE WITH YOU”…

The R6 features variable low pass crossovers for system flexibility. To eliminate any possible weak link we’ve spared no expense in offering the best possible connections with Tiffany style RCA jacks for as well as an oversize Nickle plated terminal block for power input & speaker output. 

Stable at 0.5 Ohm with a high quality Class D PCB layout that includes built in auto sensing turn on function for vehicles that do not have the ability for RCA output, selective Bass Boost EQ for fine tuning, soft delay remote turn on/off circuit that eliminates pops and clicks.

The R6 Amplifier utilizes a MOSFET power supply for high output and increased stability, variable gain control and remote level control port for optional controller. With dynamic features like its Parametric EQ with Q-Control and Built-In Auto Sensing Turn-On the Rage R6 Amplifier blends power and performance with sleek design allowing you to Rage in style. 

• Heavy Duty Textured Cast Aluminum Basket
• Reinforced Non-Pressed Paper Cone 
• EROM Hi-Tech Ribbed Foam Surround for Strength & Flexibility
• 2.5" / 61.1mm 4-Layer Hi-Temperature Voice Coil for Extended Playing 
• Double Stacked 130oz High Energy Strontium Ferrite Magnets 
• Enhanced Cooling T-yoke Design with Black Anodized Finish
• Black Anodized One Piece Pole-Plate for Added Motor Force
• Customized Rubber Gasket / Magnet Boot
• 10 Gauge Oxygen Free, Pure Copper Wire 
• Over Sized Mirror Image Dual Poly / Nomex Spiders

• Sound Quality Class-D Design
• Built-In Auto Sensing Turn-On Function (Hi-Inputs)
• MOSFET Power Supplies for High Power Output and Best Stability into Low Impedance Loads
• Soft Delay Remote Turn On/Off Circuit Eliminates Pops and Clicks
• Variable Low Pass Electronic Crossover
• Selectable Bass Boost EQ ~ 0 ~ 12dB
• Q-Control for Narrow to Wide Parametric EQ Frequency Adjustments
• Subsonic Filter Control to Filter Out Unwanted Low Frequencies 0Hz ~ 60Hz
• Self-Diagnostic Protection Circuit with LED Status Indicator for Impedance Over-load, Speaker Short Circuit, Thermal Overheating, and DC Output
• 0.5Ω Stable Operation with Extensive Output Power Increase
• Variable Gain Control
• Remote Level Control Port (for optional controller)

Two Fierce 12s Dual 4 Ohm Subwoofers matched up to the R6 Mono Block Amplifier! 

The FIERCE12s has Dual 3" Voice Coils, Ribbed Foam Surrounds with Heavy Duty Cast Aluminum Baskets. Carefully selecting each component from the Tinsel Leads, Direct Connected 10 Gauge Pure Copper Wire to the Double Stacked Strontium Ferrite Magnets we have created a Subwoofer that goes Deeper & plays Louder than our competition.

The R6 features variable low pass crossovers for system flexibility. To eliminate any possible weak link we’ve spared no expense in offering the best possible connections with Tiffany style RCA jacks for as well as an oversize Nickle plated terminal block for power input & speaker output. 

Stable at 0.5 Ohm with a high quality Class D PCB layout that includes built in auto sensing turn on function for vehicles that do not have the ability for RCA output, selective Bass Boost EQ for fine tuning, soft delay remote turn on/off circuit that eliminates pops and clicks.

The R6 Amplifier utilizes a MOSFET power supply for high output and increased stability, variable gain control and remote level control port for optional controller. With dynamic features like its Parametric EQ with Q-Control and Built-In Auto Sensing Turn-On the Rage R6 Amplifier blends power and performance with sleek design allowing you to Rage in style. 

What does all this translate to? Simply, amplifiers you can count on for rigorous competition and yet flexible and affordable enough to use as any system anchor.

• Heavy Duty Textured Cast Aluminum Basket
• Reinforced Non-Pressed Paper Cone
• EROM Hi-Tech Ribbed Foam Surround for Strength & Flexibility
• 3" / 76.5mm, 4-Layer Hi-Temperature Voice Coil for Extended Playing 
• Double Stacked 180oz High Energy Strontium Ferrite Magnets 
• Enhanced Cooling T-yoke Design with Black Anodized Finish
• Black Anodized One Piece Pole-Plate for Added Motor Force
• Over Sized Mirror Image Dual Poly/ Nomex Spiders
• Reinforced Fiberglass Woven Dustcap for High Power Applications
• Dual Impedance Black Anodized Voice Coil Former with Kevlar Spunlace
• Customized Rubber Gasket / Magnet Boot
• Stitched Cone for an Extended Lifespan
• 10 Gauge Oxygen Free, Pure Copper Wire
• Triple Black Poly Cotton Spiders with Mirror Image Layout
  
  

• Sound Quality Class-D Design
• Built-In Auto Sensing Turn-On Function (Hi-Inputs)
• MOSFET Power Supplies for High Power Output and Best Stability into Low Impedance Loads
• Soft Delay Remote Turn On/Off Circuit Eliminates Pops and Clicks
• Variable Low Pass Electronic Crossover
• Selectable Bass Boost EQ ~ 0 ~ 12dB
• Q-Control for Narrow to Wide Parametric EQ Frequency Adjustments
• Subsonic Filter Control to Filter Out Unwanted Low Frequencies 0Hz ~ 60Hz
• Self-Diagnostic Protection Circuit with LED Status Indicator for Impedance Over-load, Speaker Short Circuit, Thermal Overheating, and DC Output
• 0.5Ω Stable Operation with Extensive Output Power Increase
• Variable Gain Control
• Remote Level Control Port (for optional controller)

Four Fierce 6 Subwoofers (800 Watts RMS) + One R4 Monoblock Amplifier (1050 Watts RMS)

The FIERCE 6 can take up to 200 Watts RMS each and has 1.5" Inch Dual 4 Ohm Voice Coils that combined can be wired for a 1 ohm final load. The Fierce line-up is a result of our Design & Engineering team’s desire and our corporate willingness to give them a “green light” to create a Sub that’s happy whether it’s working or playing - Mission Accomplished! Belying their value-added pricing these Subs are true competitors in every aspect. The FIERCE 6 has Dual 1.5" Voice Coils, Ribbed Foam Surrounds, Double Stacked Strontium Ferrite Magnets, Cast Aluminum Baskets and 100% Pure Copper Wire directly hard wired into the subwoofers leads. 

The R4 features variable low pass crossovers for system flexibility. To eliminate any possible weak link we’ve spared no expense in offering the best possible connections with Tiffany style RCA jacks for as well as Nickle plated terminal blocks for power input & speaker output. Stable at 1 Ohm with a high quality Class D PCB layout that includes built in auto sensing turn on function for vehicles that do not have the ability for RCA output, selective Bass Boost EQ for fine tuning, soft delay remote turn on/off circuit that eliminates pops and clicks. The R4 Amplifier utilizes a MOSFET power supply for high output and increased stability, variable gain control and remote level control port for optional controller. With dynamic features like its Parametric EQ with Q-Control and Built-In Auto Sensing Turn-On the Rage R4 Amplifier blends power and performance with sleek design allowing you to Rage in style. 

• Heavy Duty Textured Cast Basket
• Reinforced Non-Pressed Paper Cone 
• EROM Hi-Tech Ribbed Foam Surround for Strength & Flexibility
• 1.5" / 38.8mm 4-Layer Hi-Temperature Voice Coil for Extended Playing 
• Double Stacked 70oz High Energy Magnets 
• Enhanced Cooling T-yoke Design with Black Anodized Finish
• Customized Rubber Gasket / Magnet Boot
• Triple Black Poly Cotton Spiders with Mirror Image Layout
  

• Sound Quality Class-D Design
• Built-In Auto Sensing Turn-On Function (Hi-Inputs)
• MOSFET Power Supplies for High Power Output and Best Stability into Low Impedance Loads
• Soft Delay Remote Turn On/Off Circuit Eliminates Pops and Clicks
• Variable Low Pass Electronic Crossover
• Selectable Bass Boost EQ ~ 0 ~ 12dB
• Q-Control for Narrow to Wide Parametric EQ Frequency Adjustments
• Subsonic Filter Control to Filter Out Unwanted Low Frequencies 0Hz ~ 60Hz
• Self-Diagnostic Protection Circuit with LED Status Indicator for Impedance Over-load, Speaker Short Circuit, Thermal Overheating, and DC Output
• 1Ω Stable Operation with Extensive Output Power Increase
• Variable Gain Control
• 4 AWG Power and Ground Terminals
• Remote Level Control Port (for optional controller)
  

SPECIFICATIONS:

Carefully selecting each component for the FORCE 8, from the Tinsel Leads to the Cast Aluminum Baskets to the 10 Gauge Wire to the Double Stacked Strontium Ferrite Magnets, we have created a Subwoofer series that goes Deeper & plays Louder than our competition. Plus, our inclusion of Dual Voice Coils gives you system design flexibility. Our goal was overall design balance - the ability to play loud, play deep and remain composed. With that in mind we are proud to present the end result, “MAY THE FORCE BE WITH YOU”…

The R5 features variable low pass crossovers for system flexibility. To eliminate any possible weak link we’ve spared no expense in offering the best possible connections with Tiffany style RCA jacks for as well as an oversize Nickel plated terminal block for power input & speaker output. With dynamic features like its Parametric EQ with Q-Control and Built-In Auto Sensing Turn-On the Rage R5 Amplifier blends power and performance with sleek design allowing you to Rage in style.

• Heavy Duty Textured Cast Aluminum Basket
• Reinforced Non-Pressed Paper Cone 
• EROM Hi-Tech Ribbed Foam Surround for Strength & Flexibility
• 2.5" / 61.1mm 4-Layer Hi-Temperature Voice Coil for Extended Playing 
• Double Stacked 130oz High Energy Strontium Ferrite Magnets 
• Enhanced Cooling T-yoke Design with Black Anodized Finish
• Black Anodized One Piece Pole-Plate for Added Motor Force
• Customized Rubber Gasket / Magnet Boot
• 10 Gauge Oxygen Free, Pure Copper Wire 
• Over Sized Mirror Image Dual Poly / Nomex Spiders

• 0 AWG Power / Ground Inputs 
• Sound Quality Class-D Design
  
• Built-In Auto Sensing Turn-On Function (Hi-Inputs)
• MOSFET Power Supplies for High Power Output and Best Stability into Low Impedance Loads
• Soft Delay Remote Turn On/Off Circuit Eliminates Pops and Clicks
• Variable Low Pass Electronic Crossover
• Selectable Bass Boost EQ ~ 0 ~ 12dB
• Q-Control for Narrow to Wide Parametric EQ Frequency Adjustments
• Subsonic Filter Control to Filter Out Unwanted Low Frequencies 0Hz ~ 60Hz
• Self-Diagnostic Protection Circuit with LED Status Indicator for Impedance Over-load, Speaker Short Circuit, Thermal Overheating, and DC Output
• 1Ω Stable Operation with Extensive Output Power Increase
• Variable Gain Control
• Remote Level Control Port (for optional controller)

Four of the FIERCE12 Dual 4 Ohm Subwoofers Matched up to the R6 3200 Watt RMS @ 0.5 Ohm Mono Block Amplifier! 

The Fierce line-up is a result of our Design & Engineering team’s desire and our corporate willingness to give them a “green light” to create a Sub that’s happy whether it’s working or playing - Mission Accomplished! Belying their value-added pricing these Subs are true competitors in every aspect. The FIERCE12 has Dual 2.5" Voice Coils, Ribbed Foam Surrounds, Double Stacked Strontium Ferrite Magnets, Cast Aluminum Baskets and 10 Gauge Pure Copper Wire. GET READY TO GET FIERCE…

The R6 features variable low pass crossovers for system flexibility. To eliminate any possible weak link we’ve spared no expense in offering the best possible connections with Tiffany style RCA jacks for as well as an oversize Nickle plated terminal block for power input & speaker output. 

Stable at 0.5 Ohm with a high quality Class D PCB layout that includes built in auto sensing turn on function for vehicles that do not have the ability for RCA output, selective Bass Boost EQ for fine tuning, soft delay remote turn on/off circuit that eliminates pops and clicks.

The R6 Amplifier utilizes a MOSFET power supply for high output and increased stability, variable gain control and remote level control port for optional controller. With dynamic features like its Parametric EQ with Q-Control and Built-In Auto Sensing Turn-On the Rage R6 Amplifier blends power and performance with sleek design allowing you to Rage in style. 

• Heavy Duty Textured Cast Aluminum Basket
• Reinforced Non-Pressed Paper Cone
• EROM Hi-Tech Ribbed Foam Surround for Strength & Flexibility
• 2.5" / 61.1mm 4-Layer Hi-Temperature Voice Coil for Extended Playing 
• Double Stacked 130oz High Energy Strontium Ferrite Magnets 
• Enhanced Cooling T-yoke Design with Black Anodized Finish
• Black Anodized One Piece Pole-Plate for Added Motor Force
• Over Sized Mirror Image Dual Poly/ Nomex Spiders
• Reinforced Fiberglass Woven Dustcap for High Power Applications
• Dual Impedance Black Anodized Voice Coil Former with Kevlar Spunlace
• Customized Rubber Gasket / Magnet Boot
• Stitched Cone for an Extended Lifespan
• 10 Gauge Oxygen Free, Pure Copper Wire 
• Dual Black Poly Cotton Spiders with Mirror Image Layout

• Sound Quality Class-D Design
• Built-In Auto Sensing Turn-On Function (Hi-Inputs)
• MOSFET Power Supplies for High Power Output and Best Stability into Low Impedance Loads
• Soft Delay Remote Turn On/Off Circuit Eliminates Pops and Clicks
• Variable Low Pass Electronic Crossover
• Selectable Bass Boost EQ ~ 0 ~ 12dB
• Q-Control for Narrow to Wide Parametric EQ Frequency Adjustments
• Subsonic Filter Control to Filter Out Unwanted Low Frequencies 0Hz ~ 60Hz
• Self-Diagnostic Protection Circuit with LED Status Indicator for Impedance Over-load, Speaker Short Circuit, Thermal Overheating, and DC Output
• 0.5Ω Stable Operation with Extensive Output Power Increase
• Variable Gain Control
• Remote Level Control Port (for optional controller)

Four of the FIERCE12S Dual 4 Ohm Subwoofers Matched up to the R6 3200 Watt RMS @ 0.5 Ohm Mono Block Amplifier! 

The Fierce line-up is a result of our Design & Engineering team’s desire and our corporate willingness to give them a “green light” to create a Sub that’s happy whether it’s working or playing - Mission Accomplished! Belying their value-added pricing these Subs are true competitors in every aspect. The FIERCE12S has Dual 3" Voice Coils, Ribbed Foam Surrounds, Double Stacked Strontium Ferrite Magnets, Cast Aluminum Baskets and 10 Gauge Pure Copper Wire. GET READY TO GET FIERCE…

The R6 features variable low pass crossovers for system flexibility. To eliminate any possible weak link we’ve spared no expense in offering the best possible connections with Tiffany style RCA jacks for as well as an oversize Nickle plated terminal block for power input & speaker output. 

Stable at 0.5 Ohm with a high quality Class D PCB layout that includes built in auto sensing turn on function for vehicles that do not have the ability for RCA output, selective Bass Boost EQ for fine tuning, soft delay remote turn on/off circuit that eliminates pops and clicks.

The R6 Amplifier utilizes a MOSFET power supply for high output and increased stability, variable gain control and remote level control port for optional controller. With dynamic features like its Parametric EQ with Q-Control and Built-In Auto Sensing Turn-On the Rage R6 Amplifier blends power and performance with sleek design allowing you to Rage in style. 

• Heavy Duty Textured Cast Aluminum Basket
• Reinforced Non-Pressed Paper Cone
• EROM Hi-Tech Ribbed Foam Surround for Strength & Flexibility
• 3" / 76.5mm 4-Layer Hi-Temperature Voice Coil for Extended Playing 
• Double Stacked 180oz High Energy Strontium Ferrite Magnets 
• Enhanced Cooling T-yoke Design with Black Anodized Finish
• Black Anodized One Piece Pole-Plate for Added Motor Force
• Over Sized Mirror Image Dual Poly/ Nomex Spiders
• Reinforced Fiberglass Woven Dustcap for High Power Applications
• Dual Impedance Black Anodized Voice Coil Former with Kevlar Spunlace
• Customized Rubber Gasket / Magnet Boot
• Stitched Cone for an Extended Lifespan
• 10 Gauge Oxygen Free, Pure Copper Wire 
• Triple Black Poly Cotton Spiders with Mirror Image Layout

• Sound Quality Class-D Design
• Built-In Auto Sensing Turn-On Function (Hi-Inputs)
• MOSFET Power Supplies for High Power Output and Best Stability into Low Impedance Loads
• Soft Delay Remote Turn On/Off Circuit Eliminates Pops and Clicks
• Variable Low Pass Electronic Crossover
• Selectable Bass Boost EQ ~ 0 ~ 12dB
• Q-Control for Narrow to Wide Parametric EQ Frequency Adjustments
• Subsonic Filter Control to Filter Out Unwanted Low Frequencies 0Hz ~ 60Hz
• Self-Diagnostic Protection Circuit with LED Status Indicator for Impedance Over-load, Speaker Short Circuit, Thermal Overheating, and DC Output
• 0.5Ω Stable Operation with Extensive Output Power Increase
• Variable Gain Control
• Remote Level Control Port (for optional controller)